Aggregate crushing value Test Lab Report. Adnan Abir. Name of the experiment: Aggregate Crushing value test. Objective: 1. Determine the aggregate crushing value of coarse aggregate. 2. Assess suitability of coarse aggregates for use in different types of road. Theory: The “aggregate crushing value” give a relative measure of the resistance
This test is repeated once or twice and the average crushing value of the aggregate is determined. The average crushing value in the different tests is the actual crushing value of aggregate. Important points to remember. It is recommended that the crushing value of aggregate should be less than 30%.
Calculation of Aggregate Crushing Value. The crushing value of aggregates is measured in the ratio between the crushed aggregates, obtained from the IS sieve 2.36mm and the weight of the dried aggregate sample. At least three samples should be tested from the same batch and average value to get accurate results.
1.The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = (B/A) X 100 where A = weight of oven-dried sample B = weight in 'g' of fraction passing through 2.36 mm IS sieve. 6.Video Aggregate Crushing Value Test
The aggregate crushing value is a numerical index of the resistance of an aggregate to crushing under a gradually applied compressive load. It is expressed as the percentage by mass of the crushed (or finer) material obtained when the test sample is subjected to a specified load under standard conditions.
Aggregate crushing value is defined as the percentage by weight of the crushed (or finer) material obtained when the test aggregates are subjected to a specified load under standardized conditions, and the strength of the aggregate used in road construction is expressed by numerical index .
AGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes 12.5mm, 10mm and 2.36mm. Procedure to determine Aggregate Crushing Value
The apparatus of the aggregate crushing value test as per IS: 2386 (Part IV) 1963 consists of: 1) A 15cm diameter open ended steel cylinder with plunger and base plate, of the general form and dimensions as shown in Fig 1. 2) A straight metal tamping rod
We would like to show you a description here but the site won’t allow us.
The Aggregate Crushing Value (ACV) Test Set provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Each set consists of steel cylinder, plunger, base plate, cylindrical measure and tamping rod. All parts of the apparatus are powder coated or galvanized steel, heat treated and ground
BS 812 part 110 describes a method to determine the aggregate crushing value (ACV) which gives a relative measure of the crushing resistance of aggregate under an increasing compressive load.The method is applicable to aggregates passing a 14.0 mm test sieve and retained on a 10.0 mm test sieve.
Read More: AGGREGATE CRUSHING VALUE TEST PROCEDURE AND RESULT. Objective: This method of test used to measure the impact value of aggregate use in the construction of Highway pavement and concrete structure. Reference:-IS 2386 (Part 4) 1963. Apparatus:-
Jan 25, 2018 · AGGREGATE CRUSHING VALUE TEST AIM: To find Aggregate Crushing value of the given aggregate sample. APPARATUS: Steel cylinder, cylindrical measure, Steel temping rod, Balance, Compressions testing machine PROCEDURE: The aggregate passing 12.5 mm sieve and retained on 10 mm IS sieve is selected for standard test.
1.0 AGGREGATE IMPACT VALUE TEST 1 1.0 INTRODUCTION Aggregates used in road construction, should be strong enough to resist crushing under traffic wheel loads if the aggregates are weak, the stability of the pavement structure is likely to be adversely affected.
Impact and Crushing Value Perth 0408 034 668 Melbourne 0428 315 502 Auckland 64 274 738758 Sydney The Aggregate Impact Value (AIV) Apparatus is supplied. aggregate crushing value test report Aggregate Crushing Value AGGREGATE CRUSHING VALUE (ACV) BS 812/Part 110 per test Aggregate impact value.
d) Determination of Aggregate Abrasion Value, e) Determination of the Polished Stone Value, and f) Determination of Crushing Strength. 2. DETERMINATION OF AGGREGATE CRUSHING VALUE 2.1 Object This method of test covers the procedure for determining aggregate crushing value of coarse aggregate.
The ‘ aggregate crushing value test gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load Aggregate crushing value is defined as the percentage by weight of the crushed or finer material obtained when the test aggregates are subjected to a specified load under standardized conditions
Aggregate Crushing Value Test Procedure Civiconcepts. For the Aggregate crushing value test an aggregate sample passing through 125 mm IS sieve and retained on 10mm IS sieve is selected and dried to a temperature of 105 ºC to 110 ºC then cooled to room temperature To fill the cylindrical measure mould about 65 kg of a
Jul 14, 2018· Aggregate Impact Value Test. AIV test is conducted to determine the Aggregate Impact Value of Coarse aggregate. The aggregate impact value gives a relative measure of the resistance of an aggregate to sudden shock or impact, which in some aggregates differs from Its resistance to a slow compression load.
Aggregate Impact Values, (AIV’s), below 10 are regarded as strong, and AIV’s above 35 would normally be regarded as too weak for use in road surfaces. Aggregate Impact Values and Aggregate Crushing Values are often numerically very similar, and indicate similar aggregate strength properties. Aggregate Impact Value; Test Specifications:
Jan 23, 2018· The aggregate crushing value for cement concrete pavement shall not exceed 30%. The aggregate crushing value for wearing surfaces shall not exceed 45%. PURPOSE OF TEST: The strength of coarse aggregate is assessed by aggregate crushing test, the aggregate value provide the relative measure of resistance to crushing under gradually applied
Los Angeles abrasion test on aggregates is the measure of aggregate toughness and abrasion resistance such as crushing, degradation and disintegration. This test is carried out by AASHTO T 96 or ASTM C 131: Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine. The aggregate used in surface course 
Feb 08, 2012· Impact, 10% Fines & Crushing TestsFigure 2. Apparatus for the 10% fines test and aggregate crushing test (Millard, 1993) 2. The material used for both tests is aggregate passing a 12.70 mm sieve and retained on a 9.52 mm sieve.
Dec 15, 2017· Aggregate Impact Values and Aggregate Crushing Values are often numerically very similar, and indicate similar aggregate strength properties. Classification of aggregates using Aggregate Impact Value is as given below: Aggregate Impact Value Classification <20%.= Exceptionally Strong 10 20% .=Strong 20-30%. =Satisfactory for road surfacing